LFP_48V_mBMS_FW/mBMS_APP_V3117/HARDWARE/uart2.c

#include "sys.h"
#include "delay.h"
#include "uart2.h"
#include "includes.h"					//ucos Use	  
//////////////////////////////////////////////////////////////////////////////////	 
//This program is for educational purposes only, without the author's permission, may not be used for any other purpose
//ALIENTEK STM32F4 Explorer Board
//Initialize serial port 2		   
//Hot Atomic @ALIENTEK
//Forum: www.openedv.com
//Date modified: 2015/9/12
//Version: V1.0
//All rights reserved pirated reserved.
//Copyright(C) Guangzhou wing electronic technology limited company 2009-2019
//All rights reserved
//********************************************************************************
////////////////////////////////////////////////////////////////////////////////// 	  

/* Defines -------------------------------------------------------------------*/
#define TX_BUFFER_SIZE       512
#define RX_BUFFER_SIZE       512

/* Type declarations ---------------------------------------------------------*/
typedef struct
{
	USART_TypeDef *usart;
	u16 RxInPos, RxOutPos;
	u16 TxInPos, TxOutPos;
	u8  RxBuf[RX_BUFFER_SIZE];
	u8  TxBuf[TX_BUFFER_SIZE];
} UART_Info;

/* Exported macro ------------------------------------------------------------*/
UART_Info Uart;

//Initializes IO serial port 2
//Bound: baud rate
void uart2_init(u32 bound)
{
   //GPIO port settings
	GPIO_InitTypeDef GPIO_InitStructure;
	USART_InitTypeDef USART_InitStructure;
	
	Uart.usart = USART2;
	
	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOD,ENABLE); 	//Enable GPIOD clock
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2,ENABLE);	//Enable USART2 clock
 
	//Serial port 2 pins reuse maps
	GPIO_PinAFConfig(GPIOD, GPIO_PinSource5, GPIO_AF_USART2); 	//GPIOD5 multiplex USART2 TX
	GPIO_PinAFConfig(GPIOD, GPIO_PinSource6, GPIO_AF_USART2); 	//GPIOD6 multiplex USART2 RX
	
	//USART2 port configuration
	GPIO_InitStructure.GPIO_Pin 	= GPIO_Pin_5 | GPIO_Pin_6; 		//GPIOD5, 6
	GPIO_InitStructure.GPIO_Mode 	= GPIO_Mode_AF;		//Multiplexing function
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_100MHz;	//Speed 50MHz
	GPIO_InitStructure.GPIO_OType = GPIO_OType_PP; 	//Push-pull multiplexed output
	GPIO_InitStructure.GPIO_PuPd 	= GPIO_PuPd_UP; 	//Pull-up
	GPIO_Init(GPIOD, &GPIO_InitStructure); 				//Initialize PD5, 6 for USART2 TX, RX

	//USART2 Initialization settings
	USART_InitStructure.USART_BaudRate 				= bound;				//Baud rate setting
	USART_InitStructure.USART_WordLength 			= USART_WordLength_8b;	//Word is 8-bit data format
	USART_InitStructure.USART_StopBits 				= USART_StopBits_1;		//One stop bit
	USART_InitStructure.USART_Parity 					= USART_Parity_No;		//No parity bit
	USART_InitStructure.USART_HardwareFlowControl 	= USART_HardwareFlowControl_None;	//No hardware flow control
	USART_InitStructure.USART_Mode 						= USART_Mode_Rx | USART_Mode_Tx;	//Send and receive mode
	USART_Init(Uart.usart, &USART_InitStructure); 								//Initialize serial port 2
	
	USART_Cmd(Uart.usart, ENABLE);  //Enabling serial port 2 
	
	USART_ClearFlag(Uart.usart, USART_FLAG_TC);
	
	USART_ITConfig(Uart.usart, USART_IT_RXNE, ENABLE);//Open break
}

void USART2_IRQHandler(void)                	//Serial port 2 interrupt service routine
{
	u8 rx_data;

	OSIntEnter();    
	
	if (USART_GetITStatus(Uart.usart, USART_IT_RXNE) != RESET) 
	{
		rx_data = USART_ReceiveData(Uart.usart) & 0xFF;              /* Read one byte from the receive data register.        */

		Uart.RxBuf[Uart.RxInPos++] = rx_data;
		Uart.RxInPos %= RX_BUFFER_SIZE;
        
		if (Uart.RxInPos == Uart.RxOutPos) 
		{
			Uart.RxOutPos++;
			Uart.RxOutPos %= RX_BUFFER_SIZE;
		}
		USART_ClearITPendingBit(Uart.usart, USART_IT_RXNE);          /* Clear the USART2 receive interrupt.                  */
	}

	if (USART_GetITStatus(Uart.usart, USART_IT_TXE) != RESET) 
	{
		/* Write one byte to the transmit data register */
		USART_SendData(Uart.usart, Uart.TxBuf[Uart.TxOutPos++]);
		Uart.TxOutPos %= RX_BUFFER_SIZE;
            
		if (Uart.TxOutPos == Uart.TxInPos) 
		{
			/* Disable the Transmit interrupt */
			USART_ITConfig(Uart.usart, USART_IT_TXE, DISABLE);
		}         
	}
	if (USART_GetITStatus(Uart.usart, USART_IT_TC) != RESET)
	{
		/* Disable the Transmit complete interrupt */
		USART_ITConfig(Uart.usart, USART_IT_TC, DISABLE);
	}
	OSIntExit();    	//Exit interrupt
}

/*******************************************************************************
* Function Name : void UART2_PutChar(char data)
* Description   : Send 1 byte via USART2
* Parameters    : ASCII code
* Return        : None
*******************************************************************************/
void UART2_PutChar(const u8 ascii)
{
	CPU_SR_ALLOC();

	while (((Uart.TxInPos + 1)% TX_BUFFER_SIZE) == (Uart.TxOutPos % TX_BUFFER_SIZE))
		USART_ITConfig(Uart.usart, USART_IT_TXE, ENABLE);
    
	CPU_CRITICAL_ENTER();

	Uart.TxBuf[Uart.TxInPos++] = ascii;
	Uart.TxInPos %= RX_BUFFER_SIZE;
	
	USART_ITConfig(Uart.usart, USART_IT_TXE, ENABLE);

	CPU_CRITICAL_EXIT();
}

/*******************************************************************************
* Function Name : void UART2_PutChar(char data)
* Description   : Send 1 byte via USART2
* Parameters    : ASCII code
* Return        : None
*******************************************************************************/
void UART2_PutStr(u8 *str, u16 len)
{
	u16 i;
	
	for (i = 0; i < len; i++)
	{
		UART2_PutChar(str[i]);
	}
}

/*******************************************************************************
* Function Name : u8 UART2_GetChar(char *data)
* Description   : Send 1 byte data to USART2 transmit buffer
* Parameters    : none
* Return        : Transmission result (0: buffer empty, 1: buffer has data)
*******************************************************************************/
ErrorStatus UART2_GetChar(u8 *data)
{
	if (Uart.RxInPos != Uart.RxOutPos)
	{
		data[0] = Uart.RxBuf[Uart.RxOutPos];
		Uart.RxOutPos++;
		Uart.RxOutPos %= RX_BUFFER_SIZE;
		return SUCCESS;
	}
	else
		return ERROR;
}

void UART2_Flush(void)
{
	CPU_SR_ALLOC();

	CPU_CRITICAL_ENTER();
	Uart.RxInPos  = 0;
	Uart.RxOutPos = 0;
	CPU_CRITICAL_EXIT();
}